Спасибо!

Мы исправим ошибку в ближайшее время

Сообщить об ошибке

Site Tools


Send new password

Please enter your user name in the form below to request a new password for your account in this wiki. A confirmation link will be sent to your registered email address.

Set new password for



SIM Card Inserting

Before SIM card inserting disable PIN request at activation. For this end insert the card in any cell phone and disable PIN request, according to the cell phone operating instruction.

  1. Using a sharp-pointed object press the button on the terminal front panel. The SIM card holder will eject
  2. Remove the SIM card holder from the connector slots and insert the SIM card into it with contact pieces up
  3. Insert the SIM card holder in the connector slots:

SIM-card installation

SIM chip installation is available under custom order.

Second SIM Card and SD Card Inserting for Optim

  1. Unscrew the two screws fixing the terminal body
  2. Remove the upper body part
  3. Insert a miniSD card in the slot intended for SD card
  4. Insert the second SIM card in the slot as shown in figure:

 Second SIM Card

Connector Pin Assignment

Omnicomm Profi terminals:

General view of the terminal Omnicomm Profi

Omnicomm Profi Wi-Fi terminals:

General view of the terminal Omnicomm Profi Wi-Fi

Connector Х1:

Connector Х1

No. of pin Signal name Designation Wire colour in cable
1 Ground (negative) for power supply Ground (signal) White
2 Ground (negative) for power supply Ground (power) White
3 Panic button Panic button White-red
4 Universal input 2 Input 2 Black-white
5 Universal input 4 Input 4 Black-yellow
6 RPM input Tachometer Blue
7 Controlled output 2 Output 2 Yellow-dark blue
8 Line RX RS-232 RS-232 RX Pink
9 Line B RS-485 №2 B RS-485 №2 Black-blue
10 Line B RS-485 №1 B RS-485 №1 Blue-white
11 CAN L CAN L Purple-white
12 Vehicle power supply voltage Power (positive) Red
13 Ignition key IGN Yellow
14 GSM Activation Button GSM Green-black
15 Universal input 1 Input 1 Black
16 Universal input 3 Input 3 Black-red
17 iButton+ iButton+ Pink-red
18 Controlled output 1 Output 1 Yellow-red
19 Line TX RS-232 RS-232 TX Grey
20 Line A RS-485 №2 A RS-485 №2 White-green
21 Line A RS-485 №1 A RS-485 №1 Orange-white
22 CAN Н CAN Н Purple-orange

Connector Х2:

Connector Х2

No. of pin Signal name Designation Wire colour in cable
1 Microphone- Microphone- Green-yellow
2 Speaker- Speaker- Grey-yellow
3 Ground GND White
4 Universal input 5 Input 5 Green
5 Ground GND White
6 Microphone+ Microphone+ Green-red
7 Speaker+ Speaker+ Grey-red
8 iButton- iButton- Pink-blue
9 Universal input 6 Input 6 Purple
10 Plus LLS sensor power supply PWR LLS Brown

Omnicomm Optim terminal

General view of the terminal Omnicomm Optim 2.0

Connector Х1:

Connector Х1

No. of pin Signal name Designation Wire colour in cable
1 Ground (negative) for power supply Ground (signal) White
2 Ground (negative) for power supply Ground (power) White
3 Panic button Panic button White-red
4 Universal input 2 Input 2 Black-white
5 Universal input 4 Input 4 Black-yellow
6 RPM input Tachometer Blue
7 Controlled output 2 Output 2 Yellow-dark blue
8 Line RX RS-232 RS-232 RX Pink
9 Line B RS-485 №2 B RS-485 №2 Black-blue
10 Line B RS-485 №1 B RS-485 №1 Blue-white
11 CAN L CAN L Purple-white
12 Vehicle power supply voltage Power Red
13 Ignition key IGN Yellow
14 GSM Activation Button GSM GSM Green-black
15 Universal input 1 Input 1 Black
16 Universal input 3 Input 3 Black-red
17 iButton+ iButton+ Pink-red
18 Controlled output 1 Output 1 Yellow-red
19 Line TX RS-232 RS-232 TX Grey
20 Line A RS-485 №2 A RS-485 №2 White-green
21 Line A RS-485 №1 A RS-485 №1 Orange-white
22 CAN Н CAN Н Purple-orange

Omnicomm Smart terminal

General view of the terminal Omnicomm Smart

Connector Х1:

Connector Х1

No. of pin Signal name Designation Wire colour in cable
1 Ground (minus) for power supply Ground (signal) White
2 RPM input Tachometer Dark blue
3 Not used NC
4 Not used NC
5 Line B RS-485 LLS B RS-485 LLS Blue-white
6 CAN L CAN L Purple-white
7 Vehicle power supply voltage Power Red
8 Ignition key IGN Yellow
9 Universal input 1 Input 1 Black
10 Not used NC
11 Line A RS-485 LLS A RS-485 LLS Orange-white
12 CAN Н CAN Н Purple-orange

Protective Insert Placing for Optim

The protective insert is placed after SIM cards inserting, setting the terminal and before the connection of mounting cable connector and antennas.

1. Remove protective film from the insert

2. Carefully install the protective insert in the terminal body

Reinstallation of the protective insert is not possible

3. Treat the mounting cable connector wire exit points with silicone sealant or hot-melt glue

Protective Insert Placing

Power Supply and Ignition Key

Connect Omnicomm Profi, Profi Wi-Fi terminals as per diagrams without battery disconnect switch:  without ground disconnect switch

after ground disconnect switch: after ground disconnect switch

before ground disconnect switch: before ground disconnect switch

Connect Omnicomm Optim terminals as per diagrams without ground disconnect switch: without ground disconnect switch after ground disconnect switch: after ground disconnect switch

before ground disconnect switch: before ground disconnect switch

Connect Omnicomm Smart terminals as per diagrams without ground disconnect switch: without ground disconnect switch after ground disconnect switch: after ground disconnect switch

before ground disconnect switch: before ground disconnect switch

Terminal

Omnicomm terminal shall be installed in the vehicle cabin or in specially equipped electrics boxes on the vehicle protected from atmospheric precipitation.

Drill 4 mounting holes Ø4 mm.

For Omnicomm Profi, Profi Wi-Fi terminals:

 Dimensions

For Omnicomm Optim and Smart terminals:

 Dimensions

Install the terminal and fix with self-tapping screws.

Antennas

Choose the installation site of antennas based on the antenna cable length.

It is recommended to install the GLONASS/GPS antenna on the roof of the vehicle. The GLONASS/GPS antenna must be installed on a metallic surface. It may be installed on a non-metallic surface if it is secured to the surface using glue.

The GLONASS/GPS antenna may be installed inside the vehicle, in a place providing good access to radio signal from the sky. Inside a vehicle, the antenna must be installed only on a horizontal surface and it is necessary to carry out a check of the reception quality of the GLONASS/GPS satellites.

Recommended installation site of GSM antenna: vehicle windshield or inner side of the vehicle plastic front panel.

Recommended installation site of Wi-Fi antenna of Profi Wi-Fi terminal: vehicle windshield or inner side of the vehicle plastic front panel.

Distance from antennas to any metal surface (except for the surface of installation) should be not less than 50 mm.

  1. Degrease the installation site surface
  2. Remove protective film from the double adhesive tape on the surface of antenna
  3. Attach the antenna with the adhesive side to the installation site
  4. Fix the antenna while the adhesive is setting