Спасибо!

Мы исправим ошибку в ближайшее время

Сообщить об ошибке

Site Tools


Installation

SIM Card and SD Card Inserting

Before SIM card inserting disable PIN request at activation. For this end insert the card in any cell phone and disable PIN request, according to the cell phone operating instruction.

1. Unscrew four safety screws.

SIM-card installation

2. Using a sharp-pointed object press the button at the SIM1 or SIM2 connector side. The SIM card holder will eject

3. Remove the SIM card holder from the connector slots and insert the SIM card into it with contact pieces up

4. Insert the SIM card holder in the connector slots:

SIM-card installation

5. Insert the SD cards in the respective SD1 and SD2 slots

When installing the SD cards, the Omnicomm OKO power must be switched off.

Omnicomm OKO video terminal supports SD cards up to 512 Gb.

A list of recommended SD cards:

  • Kingston SDR/128GB SDXC A1, V30, UHS-I Class 3 , Class 10
  • Kingston SDR/256GB SDXC A1, V30, UHS-I Class 3 , Class 10
  • Transcend TS128GSDXC10U1 SDXC/SDHC Class 10 UHS-I 600x (Ultimate)

6. Fix the protective cover with four screws

Connector Pin Assignment

Omnicomm OKO Terminal

General view of Omnicomm OKO video terminal

General view of Omnicomm OKO video terminal

Connector Х1:

Connector Х1

No. of pin Nameof signal Designation Wire color in cable
1 Vehicle power supply voltage Power Red
2 Ground for power – Ground (power) White
3 Output 1 Output 1 Yellow-red
4 Universal input 5 Input 5 Green
5 Universal input 2 Input 2 Black-white
6 Panic button Panic button White-red
7 Line B RS-485 LLS B RS-485 White-blue
8 CAN L CAN L Purple-white
9 Speaker - Speaker - Grey-yellow
10 Microphone - Microphone - Green-yellow
11 Vehicle power supply voltage Power Red
12 Ground for power – Ground (signal) White
13 RPM input Tachometer Blue
14 Ignition key IGN Yellow
15 Universal input 1 Input 1 Black
16 GSM activation button GSM Green-black
17 Line A RS-485 LLS A RS-485 Orange-white
18 CAN Н CAN Н Purple-orange
19 Speaker + Speaker + Grey-red
20 Microphone + Microphone + Green-red

Connector Х2:

Connector Х2

No. of pin Name of signal Designation Wire colour in cable
1 iButton- iButton- Pink-blue
2 Line RS-232 Rx Rx RS-232 Pink
3 Universal input 4 Input 4 Black-yellow
4 Output 2 Output 2 Yellow-blue
5 External sensor power supply – Ground LLS White
6 iButton+ iButton+ Pink-red
7 Line RS-232 Tx Tx RS-232 Grey
8 Universal input 3 Input 3 Black-red
9 Universal input 6 Input 6 Purple
10 External sensor power supply + Power LLS Brown

Connectors CAM1, CAM2, CAM3, CAM4:

Connector CAM Plug

No. of pin Name of signal Colour of wire
1 RX+ White-green
2 RX- Green
3 TX+ White-orange
4 DC+ Blue
5 DC+ White-blue
6 TX- Orange
7 DC- White-brown
8 DC- Brown

Power Supply and Ignition Key

Connect Omnicomm OKO video terminals as per diagrams without a ground disconnect switch: without ground disconnect switch after the ground disconnect switch: after ground disconnect switch

Do not connect the terminal before the ground disconnect switch.

Terminal

Omnicomm terminal shall be installed inside the vehicle cabin or in specially equipped electrics boxes on the vehicle protected from atmospheric precipitation.

Drill 4 mounting holes Ø5.5 mm.

Mounting dimensions

Install the video terminal and fix with self-tapping screws.

Antennas

Choose the installation site of antennas based on the antenna cable length.

Antennas should be installed inside the vehicle cabin on a flat surface.

Distance from antennas to any metal surface (except for the installation surface) should be not less than 50 mm.

We recommend installing antennas on the windshield or on the horizontal surface of the instrument panel in a place providing a good radio pick-up range of the sky.

  1. Degrease the installation site surface
  2. Remove protective film from the double adhesive tape on the surface of antenna
  3. Attach the antenna with the adhesive side to the installation site
  4. Fix the antenna while the adhesive is setting